Custom wick holders, made to fit your jar
We design and 3D print wick holders sized to your jar, tumbler or bowl. The wick stands straight and centred – in every candle of the batch.
- Net price per piece
- from PLN 3.50
- Minimum order
- 10 pcs
- Shapes
- round and straight
- Wicks
- 1–3, cotton or wooden
Loading 3D preview…
The 3D preview is not supported in this browser – configuring and quotes still work.
Your configuration
Net price per piecePLN 12.0010–49 pcsPLN 9.0050–199 pcsPLN 7.00200+ pcs
Net price per piecePLN 6.0010–49 pcsPLN 4.5050–199 pcsPLN 3.50200+ pcs
Illustrative preview. The final design is fitted to the container you send us.
How ordering works
We do not run a shop with ready-made holders. Every set is made for a specific container, so we start with your jar.
- 1
Configure and send an enquiry
Choose a holder type in the configurator and tell us about your candles. We will reply with the next steps.
- 2
Send us your container
Post us the jar, tumbler or bowl you use – ideally with a wick. We take exact measurements from it.
- 3
We design and print
We design the holder in CAD, 3D print it and test the fit on your container.
- 4
We ship it back with the holders
Your container comes back together with the finished wick holders – ready to pour.
Types of wick holders
Every holder is made to order – for the diameter and rim shape of your container. Pick the type that suits your candle and we take care of the fit.
Round holder for 1 wick
The ring rests on the jar rim and a notched arm holds the wick dead centre. The wick slides in from the side – no threading.
Classic container candles in jars and tumblers.
Open in the configurator
Holder for 2 wicks
Two arms keep the wicks at an even, fixed spacing. For wider containers where a single wick would not melt the wax to the edges.
Wide jars, mugs and shallow bowls.
Open in the configurator
Holder for 3 wicks
Three arms set 120° apart. Even wick spacing gives an even melt pool in large candles.
Candles in bowls and large containers.
Open in the configurator
Straight wick holder
A bar with clips that grip the rim on both sides. You thread the wick through the larger hole and slide it into the smaller one, sized to its diameter.
Batch production of single-wick candles.
Open in the configurator
Wooden wick holder
Instead of a round hole – a slot matched to the width and thickness of your wooden wick. Round or straight version.
Candles with a crackling wooden wick.
Open in the configurator
Straight wooden wick holder
A bar across the container with a slot for your wick. The wick stands upright and does not twist while you pour.
Jars and tumblers with a wooden wick.
Open in the configurator
How they look on real containers
Straight holder on a cut-glass tumbler 
Side clips on a threaded apothecary jar 
White holder on a black jar 
Wick tab glued to the bottom
Why the wick has to stay straight and centred
If the wick drifts or leans while the wax sets, it stays that way for good. You only notice when the candle is lit for the first time:
Uneven melt pool and tunnelling
A flame closer to one side melts the wax on that side only, leaving a thick wall of unburnt wax on the other.
Overheated glass
A wick right next to the wall heats the container strongly – risking discolouration or even cracked glass.
Soot and weaker scent throw
A crooked wick burns unevenly, soots more often and spreads the fragrance poorly.
Production losses
Every candle with a crooked wick means re-melting the wax or a customer complaint.
A made-to-measure holder instead of sticks and clothes pegs
Sticks, pegs and one-size-fits-all centring devices sit loosely on the rim and are easy to knock off. A wick holder designed for your container sits securely – on the rim, on the sides or inside the jar – and puts the wick in exactly the same spot every time. In every candle of the batch.
| Custom wick holder | Stick or peg | Universal centring device | |
|---|---|---|---|
| Fit to the container | Designed for your jar | None | One size for all |
| Stability when moved | Grips the rim or walls | Low | Medium |
| Wooden wicks | Slot sized to the wick | Difficult | Depends on model |
| 2–3 wick candles | Fixed, even spacing | Hard to keep spacing | Depends on model |
| Batch consistency | Wick always in the same place | Low | Medium |
On the rim, on the sides or inside the jar?
We choose the mounting to suit the rim of your container, so the holder does not shift while you pour or move the candles.
On the rim
The holder rests on the jar rim and an outer lip stops it from sliding off. The most common choice for jars and tumblers with an even rim.
Side clips
Clips grip the container wall from both sides. The holder stays put even on threaded jars and thick glass.
Inside
The holder rests on the rim while short lips drop into the opening and brace against the inner walls. Ideal for rolled or irregular rims where an outer clip has nothing to grip.
How to centre a candle wick – step by step
This is how you pour a candle with a wick holder. Choose a variant: a round holder with an open notch or a straight holder with a keyhole.
The animation needs WebGL – all the steps are described below.
Tips
- Warm the container slightly before pouring – the wax adheres better to the walls.
- Do not remove the holder until the wax has set completely.
- Trim the wick to a few millimetres (usually about 5 mm) before the first burn.
- With 2–3 wick candles the holder keeps the spacing – no need to measure it for every candle.
Pricing
Simple rules for businesses: the unit price depends only on the holder shape and the total quantity in your order.
| Quantity per order | 10–49 pcs | 50–199 pcs | 200+ pcs |
|---|---|---|---|
| Straight holdercotton or wooden wick | PLN 6.00 | PLN 4.50 | PLN 3.50 |
| Round holder1–3 cotton wicks or 1 wooden wick | PLN 12.00 | PLN 9.00 | PLN 7.00 |
- Minimum order: 10 pcs per model.
- Tiers are based on the total number of pieces in your order – regardless of size and shape.
- Fitting to a new container: PLN 49 net, one-off – free from 50 pcs. Repeat orders for the same container never pay for fitting again.
- Over 1000 pcs – individual quote.
Net prices; VAT is added where applicable. Shipping is quoted with your order.
Wick holder FAQ
What is a wick holder and what is it for?
A wick holder – also called a wick centring device, wick bar or wick stabiliser – keeps the wick upright and centred in the container while you pour the wax and wait for it to set. Once the candle has set, you lift it off and use it again.
How is a wick holder different from a wick sustainer (tab)?
A sustainer is the small metal tab crimped onto the bottom of the wick and glued to the base of the container. A wick holder keeps the wick in place from the top, at rim height. They work best together: the tab holds the bottom, the holder holds the top.
Why a custom holder rather than a universal one?
A universal device is one size for every container, so it sits loosely on the rim and is easily knocked. A custom holder fits the diameter and rim of your jar, so the wick lands in exactly the same spot in every candle of the batch.
Why do I need to send you my container?
Containers with the same nominal diameter differ in wall thickness, rim shape and manufacturing tolerances. With your container in hand we fit the holder and test it. We send the container back with the finished holders.
Which containers do you make wick holders for?
For the containers candles are poured in – glass, ceramic and metal: smooth and threaded glass jars, tumblers and cut glass, amber apothecary jars, ceramic bowls, metal tins and cups, and concrete pots. The more unusual the container, the more a made-to-measure holder pays off. Not sure yours will work? Send a photo and its dimensions through the form and we will check.
Do you make holders for wooden wicks?
Yes. A wooden wick is flat, so in a round hole it would twist and lean. Instead of a hole we cut a slot matched to the width and thickness of your wick – in a round holder (a ring with a bar across the centre) or a straight one (a bar with rim clips). A wooden wick holder takes one wick, exactly in the centre of the container. Give us the wick’s dimensions or send one with your container.
How many wicks can a holder take?
Straight holders and wooden wick holders take 1 wick. Round holders for cotton wicks are made for 1, 2 or 3 wicks, with the spacing matched to the container diameter.
What is the difference between an open notch and a keyhole?
With an open notch (round holders) you slide the wick in from the side after the holder is already on the container – the fastest option in production. In a straight holder you thread the wick through the larger hole and slide it into the smaller one, sized to its diameter – it sits securely and cannot slip out.
How do I measure my container for the configurator?
Measure the inner diameter of the opening – the distance between the inside edges of the rim. That is enough for the preview and an initial chat; we take exact measurements from the container you send us.
Are wick holders reusable?
Yes. Once the candle has set, lift the holder off and fit it to the next container. In batch production it is worth having several so you can pour multiple candles at once.
Which wick size should I use?
Wick choice depends on the wax, the container diameter and the fragrance oil, so a burn test is always worthwhile. We match the holder to the wick you already use – give us its dimensions or send one with your container.
How much do custom wick holders cost?
Straight holders start at PLN 3.50 and round holders at PLN 7.00 net per piece – the price depends on the total quantity in your order (minimum 10 pcs). Fitting to a new container is a one-off PLN 49 net, free from 50 pcs. See the Pricing section for the full table.
Can I buy holders in an online shop?
We do not run a shop with ready-made holders. Every set is made to order for your container – so you get a holder that genuinely fits.
Ask for a quote
Tell us about your container and the candles you make. We will reply with a quote and how to send us the container.